HRC 400 Series
B-hyve Device Sharing
Last Updated: July 2, 2024Sharing a B-hyve device is very easy to do right from your B-hyve application. To share the device with someone else: Open the B-hyve Pro or B-hyve app Tap “My B-hyve” and then tap “Devices“ Select the device you want to share access to Tap “Device Sharing“ Choose between Guest and Manager (Managers have access...
Basic controller troubleshooting
Last Updated: July 2, 2024Below are a collection of common problems and their recommended solution. Display and error codes DISPLAY: The time keeps flashing. REASON: When programmed the display will flash between the current time and the scheduled run time if the controller is scheduled to water in the next 24 hours. PROBLEM: The controller has a partial or...
Can I use a B-hyve Pro device without Wi-Fi
Last Updated: July 2, 2024Yes! B-hyve Pro connected devices work best when connected to the B-hyve servers, but a connection is not required. When connecting to a device for the first time select the option allowing you to connect over Bluetooth. The B-hyve Pro app works in a similar fashion; however, you lose access to the WeatherSense smart programming...
Can I wire 2 stations together
Last Updated: July 2, 2024The Hydro-Rain line of irrigation controllers are equipped to operate 2 stations at the same time. This is done to support users with a master valve or a pump. So if you do not have a master valve or pump can you operate two stations on a single terminal wire? Technically yes, so should you?...
Connecting to existing controller
Last Updated: July 2, 2024Homeowners: Congratulations! You have just moved into a new home and it has a connected controller already installed. To enable Wi-Fi, please download the fee B-hyve app to your device. iOS Android Once the app is installed on your device, create an account and select add device If the device has not been connected to...
Controller keeps watering
Last Updated: July 2, 2024Does your Controller (a.k.a. Clock or Timer) keep watering after it completes a cycle? If so you most likely have multiple start times programmed in. Why multiple start times Many modern controllers allow you group stations together in a program so they all run right after another. This is helpful if you have several stations...
Grow in program
Last Updated: July 2, 2024New landscapes and sod usually require additional water until they become established. A grow in schedule (or grow in program) is a short-term watering program that provides additional water and has a set end date. These schedules ensure the landscape does not dry out. Adding a Program Schedule B-hyve Pro allows you to add start...
HRC 400 Advanced Features
Last Updated: July 2, 2024The HRC 400 outdoor controller has an easy to use interface with firmware that is continuously updated as the B-hyve Ecosystem grows and develops.
HRC 400 Connecting to Wi-Fi
Last Updated: July 2, 2024Plug in the HRC 400 controller Once the controller is plugged into the power source, it will automatically look to pair with your smart device. In the top left corner of the controller screen, the “Bluetooth” icon will flash with a graduated blinking sequence. This indicates that the controller is ready to pair with a...
HRC 400 Factory Reset
Last Updated: July 2, 2024Performing a factory reset is easy to do and does not affect the settings of a controller. All settings are stored in the B-hyve cloud (if connected to Wi-Fi) and are restored to the device in a few minutes after the factory reset and a stable Wi-Fi connection. To perform a factory reset. Open the front door...
HRC 400 Installation
Last Updated: July 2, 2024The HRC 400 outdoor controller has an easy to use interface with firmware that is continuously updated as the B-hyve Ecosystem grows and develops.
HRC 400 Programming
Last Updated: July 2, 2024The HRC 400 outdoor controller has an easy to use interface with firmware that is continuously updated as the B-hyve Ecosystem grows and develops.
Lock the HRC 400 User interface
Last Updated: July 2, 2024The HRC 400 user interface can be disabled thus requiring the user to use the B-hyve or B-hyve Pro app. To lock the user interface hold the “Back” button for about 5 seconds. A padlock icon will appear indicating the buttons and dial have been disabled. The LCD screen will still display current events and...
My controller doesn’t show the weather
Last Updated: July 2, 2024You have the controller connected and all setup. Then you notice the controller is not pulling in a weather forecast or activating a delay. There could be a few reasons for this: New Construction – The address isn’t listed in any database yet. Remove the address, but leave the zip code. Incorrect address – Did...
My Controller is not finding any Wi-Fi Networks
Last Updated: July 2, 2024Sometimes your controller may not find a Wi-Fi network. There are a few steps you can take to try to resolve this issue. Top Three resolutions: When there are a large number of Wi-Fi signals available sometimes the list has to be refreshed a few times to display the one being looked for. Tap the...
Programming a controller for indexing valves
Last Updated: July 2, 2024If you have an Indexing Valve and want to use it with a controller, then this article will help with wiring and programming.
Pump Faults
Last Updated: July 2, 2024A pump fault message appearing on your controller or B-hyve app typically means that your controller is detecting a short in the wire connected to the PUMP terminal. An easy test to do is removing the wire from the PUMP terminals in your controller. Then attempt to run a station or program manually. If the...
Smart Irrigation Controller FAQ
Last Updated: November 1, 2024WHAT ARE SMART CONTROLLERS? Smart controllers, also known as weather-based controllers or “ET-based” controllers, adjust their irrigation schedules automatically based on daily weather changes and estimated plant water requirements. WHAT IS ET? ET is a common abbreviation you may hear about smart controllers. It is short for “evapotranspiration.” In horticulture, evapotranspiration measures the amount of...
Watering for 1 min or less with Rain Sensor installed
Last Updated: July 2, 2024Does your controller run for about a minute then stop? Do you have a rain sensor connected to the controller? If you answered yes to both questions you may have a faulty rain sensor or connection. A quick fix is to hold down the “Rain Delay” button for about 5 seconds. SENS OFF should appear...
Watering for 1 min or less without Rain Sensor installed
Last Updated: July 2, 2024Does your controller run for about a minute then stop? Is your Rain Sensor jumper wire missing? If you answered yes to both questions your controller may be activating a rain delay. A quick fix is to hold down the “Rain Delay” button for about 5 seconds. SENS OFF should appear in the display indicating...
What is the current HRC 400 Firmware version
Last Updated: July 2, 2024What version of Firmware should my HRC 400 be on? The most current Firmware version for the HRC 400 controllers is 76 or higher. Our factory is using firmware version 76 during the production process. Firmware version 87 was released in January 2022 and is available for download through the B-hyve app. Firmware version 87...
Which Firmware version is on my HRC 400
Last Updated: July 2, 2024Which version of Firmware is your HRC 400 controller operating on? To find out which version of firmware you have on your HRC 400 controller simply follow these steps. Turn the controller to “OFF” Press the “BACK” and “PROG” buttons for a few seconds The current firmware version will appear on the screen
Which generation of HRC 400 do I have
Last Updated: July 2, 2024Hydro-Rain launched the HRC-400 series in 2016. A few of the features include: Industry first intergraded Wi-Fi and Bluetooth 3 program slots (A, B, & C) Programming via Bluetooth with the B-hyve Pro app Based on feedback from contractors and customers Gen 2 of the HRC 400 was released in 2018. These controllers featured: Updated...